BITMAIN ANTMINER S9 (13.5TH/s) WITH POWER SUPPLY & POWER CORD-Ready for Mining

Description

BITMAIN ANTMINER S9 (13.5TH/s) WITH POWER SUPPLY
PRODUCT INFO:
BITMAIN Antminer S9 - The world's most efficient miner and world's first bitcoin mining ASIC based on the 16nm process node. Bitmains BM1387 chip is built using TSMC's 16nm FinFET technology and, delivering a record-breaking 0.098 J/GHs, is the World's most efficient bitcoin mining chip in the consumer market. Each Antminer S9 employs 189 such chips to deliver more Hashrate and efficiency than any bitcoin miner ever made
.
BITMAIN ANTMINER S9 PRODUCT SPECS:
1. Hash Rate: 13.5TH/s ±5%
2. Power Consumption: 1375W + 7% (at the wall, with APW3 ,93% efficiency, 25C ambient temp)
3. Power Efficiency: 0.098 J/GH + 7%(at the wall, with APW3 93% efficiency, 25°C ambient temp)
4. Rated Voltage: 11.60 ~13.00V
5. Chip quantity per unit: 189x BM1387
6. Dimensions: 350mm(L)*135mm(W)*158mm(H)
7. Cooling: 2x 12038 fan
8. Operating Temperature: 0 °C to 40 °C
9. Network Connection: Ethernet
10. Default Frequency: 650M
11. Power consumption figures will vary with your PSU's efficiency, the ambient operating temperature and the accuracy of the power meter.
12. There are 3 PCI-e connectors for +12V DC input on each hashing board and all 3 need to be connected to the PSU for the Hashboard to operate. Do not connect more than one PSU to the same hashing board!
13. Separate power supply to control board: there is one additional 6pin PCI-e connector on the IO board which must be connected to the PSU to get power. Be sure to power on the miner only after all the 10x PCIE connectors are connected to power supply.
BITMAIN ANTMINER POWER SUPPLY (APW3++)
Please read carefully
*The APW3++ can deliver a maximum power of only 1200W if it is connected to a 110V mains power supply. To obtain the rated power of 1600W, the APW3++ must be connected to a 220-240V mains power supply. Please check the mains power supply that is the standard in your region before ordering.
*For the S9 or T9, it needs 220V power source (or you can run two APW3++ power supplies on 110v. Please do not connect two power supply on a Hash board. You can use a power supply with two hash board, the other with the rest of the hash board and control board. )
Specifications:
Gross Weight: 2.1kg
Package size:
32.7*16.8*12.6cm
Output
*DC Voltage:12.15V
*Rated Current(220V input): 133A
*Rated Current(110V input): 100A
*Rated Power(220V input): 1600W
*Rated Power(110V input): 1200W
*Ripple & Noise: <1%
*Voltage Regulation: <2%
*Source Regulation: <1%
*Load Regulation: <1%
*Setup, Rise Time: <2s
*Power off Protection Trip Time: >9mS
*Interface Type: 5 pairs of 6 pin PCI-E connectors (i.e. 10 connectors)
*Noise Level: <43db
Input:
*Voltage Range: 100-240V AC
*Starting Voltage: 95-105V AC
*Frequency Range: 47-63Hz
*Power Factor: >0.95 (full load)
*Leakage Current: <1.5mA (220v 50Hz)
Protection
1.  Low-voltage Input:80-89V AC
2. Output Short Circuit: Yes
3. Output Overcurrent:134-185A Max.
4. Overheat Protection: Yes
Environment Conditions
1. Operating Humidity: 20% - 90% relative humidity (non-condensing)
2. The best temperature of this item to work is 15-50
?.
Dimensions:
220mm*108mm*62mm
Cooling
2 x Fan-Forced-air cooling (Front Fan & Rear Fan)
Package includes:
1 Bitmain Antminer S9 13.5Th/s
1 APW3 PSU for Antminer D3 S9 S7 L3 (
For the S9 it needs 220V power source (or you can run two APW3++ power supplies on 110v ).
1 220V PSU Heavy Duty Cord (8FT) for Antminer PSU